基于弯曲板波的延迟线振荡器的ANSYS仿真

针对复合板结构中弯曲板波谐振频率计算相对复杂的问题,建立并分析了基于弯曲板波延迟线振荡器的理论模型,计算得到A0(0阶反对称)模式板波的谐振频率为41 MHz;为了验证理论分析的结果,利用有限元软件ANSYS建立了基于弯曲板波的延迟线振荡器的3D有限元模型,并对其进行了谐响应分析以及瞬态动力学分析。谐响应分析得到A0模式的谐振频率为37.2 MHz,与理论计算结果的相对误差为9.3%;瞬态动力学分析得到A0模式的谐振频率为39.1 MHz,与理论计算结果的相对误差为4.6%。计算和仿真为基于弯曲板波的延迟线振荡器的结构设计提供了重要的依据。     

Synthesis and growth of nonlinear infrared crystal material CdSe via seeded oriented temperature gradient solution zoning method

Single crystals of CdSe were grown by using seeded oriented temperature gradient solution zoning (STGSZ) method with the sizes of 20 mm in diameter and 80 mm in length. The crystals were characterized with X-ray diffraction, transmission spectrophotometer and infrared microscope. The transmission spectra showed that the infrared transmission is above 65% and the mean absorption was 0.01-0.04 cm-1 in the range of 2.5-20 μm.With 2.797 μm Cr, Er:YSGG laser as pumping source,experiments of optical parametric oscillator (OPO) were performed by using fabricated 5mm×5mm×30mm device crystal. The signal and idler wavelengths and the output average power were respectively 4.3 μm, 8 μm and 400 μJ. Optical-to-optical conversion efficiency was obtained by 12%.     

空间用晶体振荡器热真空性能研究

空间用晶体振荡器是航天器的重要元器件,为航天器提供计时和产生标准频率.晶体振荡器的使用性能高度依赖于应用和任务环境,热应力、机械应力、辐射应力等都对石英晶体振荡器的使用性能造成影响.在空间真空热环境下,晶体振荡器使用性能与地面常压环境下有很大的不同,为了检验空间用石英晶体振荡器的热真空环境适应性,文章针对空间用石英晶体...     

C波段高稳定陶瓷谐振振荡器设计

文章介绍了利用陶瓷谐振器（CR）来提高振荡器频率稳定度的方法,并利用专用微波电路设计软件（AWR）对该方法进行了分析,同时还对压控支路进行了温度补偿设计。根据分析结果制作的C波段高稳定陶瓷振荡器取得令人满意的指标：在全温范围测试结果为温漂≤50×10^-6／℃,带内线性≤1．1,频率稳定度≤＋15MHz,相噪≤-108...     

基于DSP+CPLD杆塔冲击接地电阻测量仪设计和实现

研制了一种直接测量杆塔冲击接地电阻的仪器,本装置对电压电流通道进行同时采样,运用了TI公司DSP芯片TMS320LF2407A和可编程的复杂逻辑器件MAX7128AE作为主控芯片,同时在外面扩展了1M字的FLASHROM.并对测量方法的理论基础进行了介绍,通过实测,验证了该测量仪的准确性.     

A millimeter wave linear superposition oscillator in 0.18 μm CMOS technology

This paper presents a millimeter wave （mm-wave） oscillator that generates signal at 36.56 GHz. The ram-wave oscillator is realized in a UMC 0.18 μm CMOS process. The linear superposition （LS） technique breaks through the limit of cut-off frequency （JET）, and realizes a much higher oscillation than Jr. Measurement results show that the LS oscillator produces a calibrated 37.17 dBm output power when biased at 1.8 V; the output power of fundamental signal is -10.85 dBm after calibration. The measured phase noise at 1 MHz frequency offset is -112.54 dBc/Hz at the frequency of 9.14 GHz. This circuit can be properly applied to mm-wave communication systems with advantages of low cost and high integration density.     

A power scalable PLL frequency synthesizer for high-speed △-∑ ADC

A 35-130 MHz/300-360 MHz phase-locked loop frequency synthesizer for △-∑ analog-to-digital con- verter （ADC） in 65 nm CMOS is presented. The frequency synthesizer can work in low phase-noise mode （300-360 MHz） or in low-power mode （35-130 MHz） to satisfy the ADC＇s requirements. To switch between these two modes, a high frequency GHz LC VCO followed by a divided-by-four frequency divider and a low frequency ring VCO followed by a divided-by-two frequency divider are integrated on-chip. The measured results show that the fre- quency synthesizer achieves a phase-noise of-132 dBc/Hz at 1 MHz offset and an integrated RMS jitter of 1.12 ps with 1.74 mW power consumption from a 1.2 V power supply in low phase-noise mode. In low-power mode, the frequency synthesizer achieves a phase-noise of-112 dBc/Hz at 1 MHz offset and an integrated RMS jitter of 7.23 ps with 0.92 mW power consumption from a 1.2 V power supply.     

高功率准分子激光MOPA系统中的三路激光准直技术研究

光束自动准直是大型激光装置中的重要组成部分。以准分子(XeCl)激光主振荡功率放大(MOPA)系统中一个典型的像传递单元为例,着重介绍了准直基准的建立、3路激光自动准直的原理、电荷耦合元件(CCD)图像采集与分析处理。通过实验验证,该准直单元准直效率高,准直精度能够满足MPOA系统的光束准直要求。     

基于 VCTCXO 的高稳定度时钟设计

高稳定度时钟广泛应用于广播电视播出发射系统中。基于GPS授时功能,将GPS秒脉冲信号（1 PPS）分频处理,可大大减少随机误差,时钟用分频后的1 PPS微调,可得到高稳定度时钟。利用低成本的VCTCXO和STM32F051单片机等器件设计了一个高稳定度时钟模块,介绍了设计思路及设计过程,包括电路框图、程序流程等,经测试,频率均方误差小于2×10-9。时钟模块成本低、体积小、使用灵活,具有较高的应用价值。     

基于改进Duffing理论的轴承微弱故障信号判断

分析了传统Duffing振子混沌系统的基本理论对检测微弱信号的不足,给出了基于改进之后的Duffing振子检测微弱信号的新方法。改进后的方法能够弥补传统方法对系统固有频率的限制,检测具有较大固有频率的微弱信号。本文主要利用传统方法和改进方法分别对轴承外圈故障信号进行验证性分析,发现改进方法能更好的找出微弱故障信号。通过对仿真信号分析和轴承故障诊断实验,结果验证了本文方法的有效性。